INFO: How to Enable EDGE for the E6

[Alpha43]

Hello,

While the site was down there was a discovery that the E6 can have edge enabled. Its the same edit that was used for the E2. Good work for the crew who made the E2 edit a while ago.

So to activate EDGE on ROKR E6 we need:
1. RadioComm 10.3.1 or newer
2. Of course A Rokr E6
3. A basic knowledge of RadioComm.
4. A service provider that has EDGE network

In RadioComm click on the GSM 2 tab directly below it is Stelem/Rdelem box in those box's enter.

Element ID= 0341
Record #= 0001
Offset= 0000
Length= 0001
after you entered the information press the Rdelem button. in the Data box you will get the seem in HEX.
original seem
FF (yours maybe different)
Change it to:
01
After you change it press Stelem button. Move to next step.

Element ID= 0340
Record #= 0001
Offset= 0000
Length= 0008
after you entered the information press the Rdelem button. in the Data box you will get the seem in HEX.
original seem
0000000000000000 (yours maybe different)
Change it to:
0905030201020000
After you change it press Stelem button. Move to next step.

Element ID= 02AF
Record #= 0001
Offset= 0000
Length= 0008
after you entered the information press the Rdelem button. in the Data box you will get the seem in HEX.
original seem
002700FA20000000 (yours maybe different)
Change it to:
007500FA20000000
After you change it press Stelem button. Move to next step.

This step is optional. The difference is 01 icon stays on, 03 the icon is only on when connected. It's a matter of preference.
Element ID= 010A
Record #= 0001
Offset= 0000
Length= 0001
after you entered the information press the Rdelem button. in the Data box you will get the seem in HEX.
original seem
01 (always on when in EDGE coverage)
Change it to:
03 (only when connected)
After you change it press Stelem button. Move to next step.

Element ID= 0032
Record #= 0001
Offset= 0000
Length= 0200
after you entered the information press the Rdelem button. in the Data box you will get the seem in HEX.
original seem
(Depends on if you've made any changes before. so default will not be posted)
How to change it.
scroll through the data box look for FEFEFF03 change the 3 to 7
After you change it press Stelem button. Move to next step.

Click on Restart, when phone reboots enjoy EDGE.

Good luck!

~Alpha~

[Cokeman]

Some have reported that the 02AF seem is different default. If your seem is
002700FA00000000 simply change it to 007500FA00000000

Element ID= 02AF
Record #= 0001
Offset= 0000
Length= 0008
after you entered the information press the Rdelem button. in the Data box you will get the seem in HEX.
original seem
002700FA20000000 (yours maybe different)
Change it to:
007500FA20000000
After you change it press Stelem button. Move to next step.

[Alpha43]

thanks for that info cokeman.

~Alpha~

[kdc803]

I would love to have edge on my rokr but I have no idea how to make sense of the post. Can anyone dumb it down for a newbie

[Alpha43]

We really cant make it easier then whats written.. Open up radiocomm and look and read at the same time. It should help.

~Alpha~

[cv144]

Alpha, I mod my A1200 with this and it works! could you post it to the how to section of A1200 forums?

Thanks

[Pondo]

Where do i get RadioCOmm at?

[TheSin]

This step is optional. The difference is 01 icon stays on, 03 the icon is only on when connected. It's a matter of preference.
Element ID= 010A
Record #= 0001
Offset= 0000
Length= 0001
after you entered the information press the Rdelem button. in the Data box you will get the seem in HEX.
original seem
01 (always on when in EDGE coverage)
Change it to:
03 (only when connected)
After you change it press Stelem button. Move to next step.

Element ID= 0032
Record #= 0001
Offset= 0000
Length= 0200
after you entered the information press the Rdelem button. in the Data box you will get the seem in HEX.
original seem
(Depends on if you've made any changes before. so default will not be posted)
How to change it.
scroll through the data box look for FEFEFF03 change the 3 to 7
After you change it press Stelem button. Move to next step.

Just a quick question, is the first one optional here or both? I don't want to do the optional one, but i also don't want to brick my phone, just for others info I'm doing this on an A1200 with generic 53P on it, so I'll report back after I get this answer.

[TheSin]

This step is optional. The difference is 01 icon stays on, 03 the icon is only on when connected. It's a matter of preference.
Element ID= 010A
Record #= 0001
Offset= 0000
Length= 0001
after you entered the information press the Rdelem button. in the Data box you will get the seem in HEX.
original seem
01 (always on when in EDGE coverage)
Change it to:
03 (only when connected)
After you change it press Stelem button. Move to next step.

Element ID= 0032
Record #= 0001
Offset= 0000
Length= 0200
after you entered the information press the Rdelem button. in the Data box you will get the seem in HEX.
original seem
(Depends on if you've made any changes before. so default will not be posted)
How to change it.
scroll through the data box look for FEFEFF03 change the 3 to 7
After you change it press Stelem button. Move to next step.

Just a quick question, is the first one optional here or both? I don't want to do the optional one, but i also don't want to brick my phone, just for others info I'm doing this on an A1200 with generic 53P on it, so I'll report back after I get this answer.

okay so I did the last step then went back and did the optional one, I prefer it with the optional one, but it does seem to be working, I'm going to attempt it on my second phone now to is on 46P generic, let you guys know how that works out.

[Alpha43]

Alpha, I mod my A1200 with this and it works! could you post it to the how to section of A1200 forums?

Thanks

I will what speeds are you getting with the Ming?

~Alpha~