[INFO] Flashing with RSD Lite & Troubleshooting Guide

[V.Razr.X]

Haveyou tried to manually select your network/band and then switch them back to automatic?

[ideliver]

Could you tell me where and how to do that?

Thanks

[andre2you]

Hello All,

I'm trying to flash to 46p and am having some issues. I can get the phone in MBM mode (red Screen) but when I plug the phone in my USB ports I get the message NS FLASH Bulverde and then a pop-up that says Windows could not load the installer for USB. Anyone have an idea whats going on? I did unrar the motopcdrivers but was not able to install them.

[kitskidd]

How do I find out which firmware im running... I have ming with Rogers.. and have put all settings in.. I also get a blank fax and email message when I get a VM.... annoying... and Im new to flashing.. iv read all the posts.. V.. you really have some extensive knowledge on this phone! nice work brutha.. can i just go somewhere and have someone flash it for me.. lol.. i don't want to screw something up.. from what i have read from this thread, lotsa things can go wrong...

[Alpha43]

Hey,
honestly flashing is alot easier then you might expect. All you need is the usb wire, the firmware, and the program. I say you should try it out.. If anything people on this forum including myself would be glad to help you out.
By the way, to check your firmware in the dial pad press insert ... WWW008W. It should then flash the information you seek.
~ALpha~

[ideliver]

OK, finally I am connected again, after the update the antennae seemed to not be connected anymore. .after turning it off and on several times it finally connected again. Everything is working again mms, INTERNET but my email still has not worked. I last set it up in April and it has worked great until the update. It keeps saying it cannot find host. I am using Cingular and I had always used MediaNet to connect to Starband INTERNET service I know I am doing something wrong but have not figured it out yet. Any suggestions?

[andre2you]

Hello All,

I'm trying to flash to 46p and am having some issues. I can get the phone in MBM mode (red Screen) but when I plug the phone in my USB ports I get the message NS FLASH Bulverde and then a pop-up that says Windows could not load the installer for USB. Anyone have an idea whats going on? I did unrar the motopcdrivers but was not able to install them. It keeps saying unable to install Hardware.

Does anyone have any idea what I'm doing wrong? The boot module on my phone is: BOOT_G_00.01.89P_HAINAM

I trying to use RSD Lite 2.7, 2.8 or 2.5 and nothing working. Mobile phone tools work perfectly.

[linelock]

Hello All,

I'm trying to flash to 46p and am having some issues. I can get the phone in MBM mode (red Screen) but when I plug the phone in my USB ports I get the message NS FLASH Bulverde and then a pop-up that says Windows could not load the installer for USB. Anyone have an idea whats going on? I did unrar the motopcdrivers but was not able to install them.

Hi andre, I was having the same issue. I don't know why because it was working before, don't know what I changed. But anyway I checked the setupapi.log file in my \Windows\ directory and it showed that it was trying to load mot_ci.dll in \windows\system32 but couldn't find it. So I did a search and found a copy in \Program Files\Common Files\Motorola Shared\MotPCSDrivers\P2K\ .I copied it to my \Windows\System32 directory and then was able to install the MOTPCS drivers when I plugged the phone in in FLashmode.

Good luck.

[andre2you]

Hello All,

I'm trying to flash to 46p and am having some issues. I can get the phone in MBM mode (red Screen) but when I plug the phone in my USB ports I get the message NS FLASH Bulverde and then a pop-up that says Windows could not load the installer for USB. Anyone have an idea whats going on? I did unrar the motopcdrivers but was not able to install them. It keeps saying unable to install Hardware.

Does anyone have any idea what I'm doing wrong? The boot module on my phone is: BOOT_G_00.01.89P_HAINAM

I trying to use RSD Lite 2.7, 2.8 or 2.5 and nothing working. Mobile phone tools work perfectly.

Ok All for some strange reason I started P2K and plugged my a1200 in and all the drivers installed. I was able to flash to 46p and it completed successfully. Now my problem that now I get no cingular bars the antenna is on phone seems to function fine. GPRS in enabled. Has anyone had this happen to them?

Can anyone help?

[andre2you]

Hello All,

I'm trying to flash to 46p and am having some issues. I can get the phone in MBM mode (red Screen) but when I plug the phone in my USB ports I get the message NS FLASH Bulverde and then a pop-up that says Windows could not load the installer for USB. Anyone have an idea whats going on? I did unrar the motopcdrivers but was not able to install them.

Hi andre, I was having the same issue. I don't know why because it was working before, don't know what I changed. But anyway I checked the setupapi.log file in my \Windows\ directory and it showed that it was trying to load mot_ci.dll in \windows\system32 but couldn't find it. So I did a search and found a copy in \Program Files\Common Files\Motorola Shared\MotPCSDrivers\P2K\ .I copied it to my \Windows\System32 directory and then was able to install the MOTPCS drivers when I plugged the phone in in FLashmode.

Good luck.

Thanks That was it. Now my problem is that I have no cingulr bars (no cingular connection)