Bluezx

[amitn18]

@Halftux
Thanks. Will try the application in the evening.

[Off thread: Where in Germany do you live? I will soon be coming to Mainz so wanted to ask a few general questions.]

[atulgoswami21]

Thanks dear,

But i cant try this as i forgot my usb cable at home. any way lots of thanks.
And hope future comes soon.
Future
- saving of network settings for usb
- gprs share over bluetooth
- maybe bridge function between bluetooth and usb to connect two pc together
- layout improvement

[atulgoswami21]

Dear while installing the pkg file it shows it is not standard document pkg.

[ady_thakur]

Have u tried making it .mpkg and installing??

[atulgoswami21]

Have u tried making it .mpkg and installing??

I have tried but no success.

Help Me guys....

[Halftux]

Sorry I am an A1200 noob. I dont know what is missing.
But pkg/mpkg is tar.gz so I would suggest to extract a package which was installed successful. And compare the x.desktop file with the one from bluez. Then adding all missing entries save in utf8 format and repack bluez and try to install it again.

[Halftux]

I tried the Guide but the problem is that when I start the bluezx manager it shows my address as all 0.
Could u help me.
I am able to do once in past(2 month back). but now it shows all 0.
Could i have to change some file.

Could you please start bluez so it shows the 0. After this please go to /mmc/mmca1/local/sbin with ekonsole there run the command:

./hciconfig > hci.txt

and post the contents from hci.txt please.

[khlystovav]

My hci.txt:

hci0: Type: UART
BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
DOWN
RX bytes:0 acl:0 sco:0 events:0 errors:0
TX bytes:8 acl:0 sco:0 commands:2 errors:0

[Halftux]

Ok the bluetooth chip is on but not right configured.
Type following in the console and check with hciconfig if still no mac adress assigned.

insmod /mmc/mmca1/local/lib/modules/bluez.o
insmod /mmc/mmca1/local/lib/modules/hci_uart.o
cd /mmc/mmca1/local/sbin
./bton
./ezx-hciattach
./hciconfig hci0 up

If no address is assigned run /mmc/mmca1/.system/QTDownload/bluezx/scripts/bluezx_shutdown.sh to unload modules and stop hci or restart phone. After this try the following in the console. It should now show a mac-address otherwise report some errors or strange behavior.

insmod /mmc/mmca1/local/lib/modules/bluez.o
insmod /mmc/mmca1/local/lib/modules/hci_uart.o
cd /mmc/mmca1/local/sbin
./bton
/usr/SYSbt/mbtdload /dev/ttyS1 1 921600 <mya1200btaddr> 1 0 -1
./ezx-hciattach
./hciconfig hci0 up

mya1200btaddr is something like this 010203040506 you can take any valid address you like or look on the sticker inside your phone.

[khlystovav]

Step1:

MontaVista(R) Linux(R) Consumer Electronics Edition 3.1
Linux/armv5tel 2.4.20_mvlcee31-mainstone_pxa27x


MotoMing login: root


MontaVista(R) Linux(R) Consumer Electronics Edition 3.1

root@MotoMing:~# insmod /mmc/mmca1/local/lib/modules/blue
insmod /mmc/mmca1/local/lib/modules/bluez.o
insmod /mmc/mmca1/local/lib/modules/hci_uart.o
cd /mmc/mmca1/local/sbin
./bton
./ezx-root@MotoMing:~# insmod /mmc/mmca1/local/lib/module
/hciconfig hci0 uproot@MotoMing:~# cd /mmc/mmca1/local/sb
root@MotoMing:/mmc/mmca1/local/sbin# ./bton
root@MotoMing:/mmc/mmca1/local/sbin# ./ezx-hciattach
root@MotoMing:/mmc/mmca1/local/sbin# ./hciconfig hci0 upi
/lib/modules/bluez.o
hci0:   Type: UART
        BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MT
        DOWN
        RX bytes:0 acl:0 sco:0 events:0 errors:0
        TX bytes:0 acl:0 sco:0 commands:0 errors:0

root@MotoMing:/mmc/mmca1/local/sbin# insmod /mmc/mmca1/lo
rt.o
insmod: a module named hci_uart already exists
root@MotoMing:/mmc/mmca1/local/sbin# cd /mmc/mmca1/local/
root@MotoMing:/mmc/mmca1/local/sbin# ./bton
root@MotoMing:/mmc/mmca1/local/sbin# ./ezx-hciattach
Can't set device: No such file or directory
root@MotoMing:/mmc/mmca1/local/sbin# ./hciconfig hci0 up

001B524CC49E address on the sticker inside my phone. In BlueSoleil adress my phone 00:1C:C1:41:B1:53.
Step2:

MontaVista(R) Linux(R) Consumer Electronics Edition 3.1
Linux/armv5tel 2.4.20_mvlcee31-mainstone_pxa27x


MotoMing login: root


MontaVista(R) Linux(R) Consumer Electronics Edition 3.1

root@MotoMing:~# insmod /mmc/mmca1/local/lib/modules/bluez.o
al/lib/modules/hci_uart.o
cd /mmc/mmca1/local/sbin
./root@MotoMing:~# insmod /mmc/mmca1/local/lib/modules/hci_uart.o
bton
/usr/SYSbt/mbtdload /dev/ttyS1 1 921600 001B524CC49E 1 0 -1
./ezxroot@MotoMing:~# cd /mmc/mmca1/local/sbin
root@MotoMing:/mmc/mmca1/local/sbin# ./bton
hciattach
./hciconfig hci0 uproot@MotoMing:/mmc/mmca1/local/sbin# /usr/SYSbt/mbtdload /dev
/ttyS1 1 921600 00
1B524CC49E 1 0 -1
root@MotoMing:/mmc/mmca1/local/sbin# ./ezx-hciattach
root@MotoMing:/mmc/mmca1/local/sbin# ./hciconfig hci0 up
Can't init device hci0: Connection timed out (110)
root@MotoMing:/mmc/mmca1/local/sbin#